Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Oldcastle Driveway & Pavers: The Riverside Owner’s Guide
We stock and install Oldcastle-compatible driveway pavers and replacement units throughout Riverside, with typical installed pricing between $700 and $2,800 for a targeted paver repair and $7,000 to $18,000 for a full paver driveway replacement. Most homeowners call us after a rainstorm in Riverside reveals a sunken paver, or after a car tire catches the lip of a cracked unit that shifted during a hot summer. The good news: matching an Oldcastle paver is usually straightforward once we see the color, profile, and thickness, and we can often complete a spot repair in a single visit.
What we see most often in Riverside is a paver that has settled or cracked because the base underneath was never compacted properly, or because irrigation water has been running against the edge for years. The paver itself is rarely the weak point in the system. Oldcastle makes a dense, consistent concrete paver. What fails first is usually what sits beneath it.
Which Oldcastle Models This Applies To
Oldcastle produces paver lines under several brand names, and matching the right unit matters more than most homeowners expect. The most common Riverside installations we encounter include the Holland stone, the Brussels Block, the Cobble paver, and the more angular Mattoni and Promenade lines. Each of these has a different face profile: Holland stone has a slight bevel, Brussels Block has a rounded, tumbled edge, and Cobble units read as a tighter, smaller-scale stone. You cannot swap a Brussels Block for a Holland stone without it being noticeable from the driveway edge.
To identify what you have, flip over a loose paver. Oldcastle units carry a stamped or cast manufacturer mark on the underside, though older installations from the 1990s and early 2000s may have worn or faint markings. Measure the paver thickness: most Oldcastle driveway pavers in California are sold at 60mm or 80mm thickness. Driveway installations should use 80mm units, while 60mm belongs on patios and walkways. We have seen Riverside driveways where a contractor used 60mm units and saved money up front, only to see cracking within five years. If your existing pavers are 60mm and the driveway sees daily vehicle traffic, that thickness mismatch is likely part of the problem. OEM units from Oldcastle are always our first recommendation for repairs, though quality aftermarket equivalents from Belgard and Unilock exist for some profiles. Penhallow Remodeling Riverside is an independent service provider and not affiliated with Oldcastle.
Styles & brands we work with
Signs Your Oldcastle Driveway & Pavers Are Failing
- Sunken or low spots after rain. Water pools tell you the base layer has settled or washed out beneath the pavers. In Riverside’s clay-heavy soils, this is the number one issue we see, especially in older Arlington neighborhood homes where drainage was an afterthought.
- Cracked pavers along tire paths. A cracked paver in the wheel track usually means the unit is 60mm where it should be 80mm, or the base was too thin. One cracked paver is a warning; three in a line means the base is failing.
- Gaps opening between pavers. Edging that has shifted lets the whole field drift. Riverside’s dry-summer, wet-winter cycle expands and contracts the joint sand, and once the edge restraint fails, pavers walk outward.
- Weeds or ants pushing through joints. This is more than cosmetic. Weeds and ant colonies mean joint sand is gone and water is entering the base. Each wet season, that water does a little more damage.
- Rocking or rattling pavers underfoot. A paver that moves when you step on it has lost its bedding sand contact. Drive on it long enough and the unit cracks at the unsupported corner.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Riverside, a spot repair on an Oldcastle paver driveway typically runs $700 to $2,800 depending on how many units are involved, whether we need to reset the base in that area, and how much cutting is required to match the existing pattern. A full paver driveway replacement runs $7,000 to $18,000, driven by square footage, paver thickness, base reconstruction depth, and access. If your driveway sits behind a narrow side gate, expect the higher end of the range because every wheelbarrow of material moves by hand.
Every repair we do includes removal of the failed pavers, inspection and correction of the base layer, new bedding sand, resetting the units to match the existing pattern, and fresh joint sand compacted into place. We write the price before we start, and that number is the number on the invoice. If the repair fails within 365 days, we come back and fix it at no charge under our Done Right Promise. That promise is in writing, on every job, every time.
DIY or Call Us?
For a homeowner, the safe and useful diagnostic work is simple: identify whether your paver is 60mm or 80mm, note where the damage sits (wheel path vs. edge), and look for obvious water flow against the driveway. You can also snap photos in morning light, which makes paver color and texture easier to match. Those details save us a trip and help us bring the right units on the first visit.
Where DIY goes wrong is lifting pavers without addressing the base. If you reset a paver on top of a base that is still failing, it will sink again inside a season. And cutting pavers to fit an edge pattern with a concrete saw is dusty, loud work that is easy to do badly. We have seen Riverside homeowners spend a weekend on a repair that failed the next winter, then call us anyway. If the base is sound and one paver is simply cracked, a handy owner can sometimes manage the swap. If there is any doubt about what is underneath, call (341) 895-1170 and we will tell you straight what the repair needs and what it costs.
FAQs
An Oldcastle paver driveway installed with a proper 80mm unit and a compacted base typically lasts 25 to 40 years in Riverside’s climate, but the base itself may need attention every 15 to 20 years. If you want an exact read on your driveway’s remaining life, call (341) 895-1170 and we’ll take a look.
Yes, most sunken or cracked Oldcastle pavers can be repaired in place by lifting the affected area, correcting the base and bedding sand, and reinstalling the units to match the original pattern. The exception is widespread base failure under most of the driveway, which makes a full replacement the smarter money. We’ll tell you which one you have before we quote anything.
A spot repair on a small failed section usually takes one day on site, including base correction, paver reset, and joint sand compaction. A full driveway replacement in Riverside typically runs three to five working days depending on square footage and access. We’ll give you a defined arrival window before the crew shows up.
We keep common Oldcastle profiles and colors in stock for Riverside jobs, including Holland stone and Brussels Block in standard Riverside-area tones, and we source specific units from recognized trade suppliers when a project calls for an exact match. Tell us the measurements and a photo, and we’ll confirm we can get it before we schedule. Call (341) 895-1170 for a free estimate, and we’ll have a real person on the phone.
Written by Trevor Nash, Owner, Penhallow Remodeling Riverside at Penhallow Remodeling Riverside, serving Riverside and nearby areas.
