Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Fence Installation: The Riverside Owner’s Guide
KraftMaid fence installation in Riverside typically runs $3,500 to $9,000 fully installed, depending on linear footage, fence height, and whether you’re replacing an existing run or starting fresh. We stock KraftMaid-compatible fence panels and hardware on our trucks, and most residential installations are completed in two to four days once permits clear. Homeowners usually call us after a windstorm twists a panel off its rails, or when a gate starts dragging against the concrete because the hinge post has shifted out of plumb.
You’re likely here because something on your KraftMaid fence gave way, or it’s been sagging long enough that you’re tired of looking at it. Either way, we can match the part, price the fix in writing, and get it installed without turning your backyard into a construction zone for a month. One thing to know before we go further: Penhallow Remodeling Riverside is an independent contractor. We are not a KraftMaid dealer or affiliate, but we work with their fence systems regularly and know the sizing, hardware, and failure points better than most generalists in Riverside.
Which KraftMaid Models This Applies To
KraftMaid is better known for cabinetry, but their fence line shows up in a fair number of Riverside backyards, particularly in neighborhoods like Canyon Crest and Mission Grove where homes were built or renovated between roughly 2005 and 2018. The fence systems we see most often are the Craftline and Seasons series, both of which use a routed panel-and-rail design rather than face-nailed pickets. That matters because replacing a single broken panel on a routed system requires matching the rail profile exactly. A generic box-store panel won’t seat correctly, and forcing it leaves gaps that get worse when the Santa Ana winds hit in the fall.
If you’re trying to identify your part, look for a small stamped code on the inside of the top rail or on the gate hinge plate. KraftMaid panels are typically 6 feet wide by 6 feet tall in Riverside, though some older installations used 5-by-6 sections. For OEM parts, you’re looking at $85 to $140 per panel before labor, and lead times from KraftMaid can stretch to three or four weeks. Quality aftermarket equivalents from suppliers we trust run $65 to $110 per panel and are usually in our Riverside shop within a week. The key compatibility gotcha is the rail pocket depth: KraftMaid’s Season line uses a 3/4-inch deep pocket, while the Craftline uses 1/2-inch. Measure before you order anything, or let us measure for you.
We also keep common KraftMaid gate hardware on hand, hinge sets, latch assemblies, and drop rods. If your gate has started to sag, the fix is usually a new hinge post set in fresh concrete, not just a hinge swap. Riverside’s clay-heavy soil expands and contracts with moisture, and that movement slowly pushes posts out of alignment. A new hinge on a moving post is a two-month fix, not a real one.
Styles & brands we work with
Signs Your KraftMaid Fence Installation Is Failing
- Panels rattling in the wind: This usually means the bottom rail fasteners have worked loose or the routed pockets have started to widen. On KraftMaid’s routed system, a loose panel will eventually split the rail end if it isn’t re-seated and fastened.
- Gate dragging or sticking at the latch side: The hinge post has moved. In Riverside’s expansive clay soil, posts can shift a half-inch or more between wet winters and dry summers. You can shim the hinges, but the real fix is resetting the post in a deeper concrete footing.
- Post lean at the fence line: If a post leans more than a few degrees, the footing wasn’t deep enough for the soil conditions. Riverside code requires fence posts set at least 2 feet deep for a 6-foot fence, and in some hillside areas, 30 inches is smarter.
- Splitting or graying panels: Riverside’s UV exposure is hard on wood and wood-composite panels. KraftMaid’s composite rails hold up better than their wood trim pieces, which tend to crack along the grain after eight to ten years of direct sun.
- Rust staining below gate hinges: The original zinc-coated hardware has worn through. This is more than cosmetic; corroded hinge pins can snap suddenly and drop the gate onto the latch post, which usually destroys the panel.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full KraftMaid fence installation in Riverside runs $3,500 to $9,000. That range covers the usual spread: a simple 50-foot run with a single gate sits near the bottom, while a 150-foot perimeter with two gates, post replacement, and tear-out of the old fence lands at the top. Material costs break down to roughly $18 to $28 per linear foot for KraftMaid-compatible panels and rails, with labor making up the remaining 40 to 50 percent of the total.
What drives the price up in Riverside specifically: hillside lots that require stepped panels, old concrete footings that need jackhammer work, and fence lines near mature trees where roots force post placement adjustments. Every quote we write includes tear-out and haul-away of the old fence, new pressure-treated posts set in concrete, all panels, rails, and hardware, and final grading of the fence line. There is no change order at the end because we give you a written number before we pick up a tool. That’s just how this works.
And for the record, every fence installation we do in Riverside carries the 365-Day Done Right Promise in writing. If a post shifts, a panel splinters, or a gate latches wrong within the first year, we come back and fix it at no charge. No re-inspection fee, no argument, no second invoice.
DIY or Call Us?
There are a few things you can safely check yourself. Look at the gate hinges to see if the screws have backed out. Examine fence panels for visible splits, especially at the bottom rail pockets. If the posts themselves are solid and the panels are intact, a sticking gate might just need a hinge adjustment and some lubricant on the latch. That’s honest work you can do in an afternoon with a cordless drill.
What we don’t recommend doing yourself is resetting posts, digging new footings along a property line, or attempting panel replacement on a routed KraftMaid system. There’s no high-tension danger here like you’d find with garage door springs, but there is a real hassle factor: hitting buried irrigation lines, getting the reveal spacing wrong so panels bind on the rails, and discovering halfway through that your property line isn’t where the old fence sat. Utility locating in Riverside is free through 811, but it takes a few days, and most homeowners don’t know that a fence over 6 feet tall requires a permit from the City of Riverside.
If you want a number for the whole job, parts and labor, call (341) 895-1170. We’ll walk the fence line, measure the rails, and hand you a written quote. The estimate is free, and so is the second visit if you have questions after we leave.
FAQs
A properly installed KraftMaid fence in Riverside lasts 15 to 20 years, but the gate hardware usually needs replacement around year 8 to 10. The composite rails and panels are the durable part; the wood trim pieces and the original zinc hardware are what fail first in our dry, high-UV climate. Call (341) 895-1170 if your fence is past the decade mark and you want an honest assessment of what’s left in it.
A single split panel can sometimes be repaired with construction adhesive and clamp time, but if the rail pocket has cracked or the panel has pulled free of the bottom rail, replacement is the only fix that holds. Repairs on routed fence systems tend to fail at the original stress point within a few months. We’ll tell you straight whether a $25 repair will hold or whether you need a $95 panel. Call (341) 895-1170 and we’ll take a look.
Most Riverside fence replacements take two to four days, assuming weather cooperates and the old footings don’t require extensive demolition. Permitting with the City of Riverside adds a week or two on the front end for fences over 6 feet. We handle the permit, the 811 utility locate, and the tear-out. Call (341) 895-1170 for a timeline based on your specific lot.
We carry KraftMaid-compatible panels, rails, gate hardware, and post anchors in our Riverside shop for the most common sizes. Odd sizes or exact OEM panel matches with specific trim profiles may take a week to source. Either way, we’ll give you a written price before any order is placed, so you’ll know exactly what the parts cost and exactly when the install happens. Call (341) 895-1170 with your measurements and we’ll check stock while you’re on the phone.
Written by Trevor Nash, Owner, Penhallow Remodeling Riverside at Penhallow Remodeling Riverside, serving Riverside and nearby areas.
